Wiring a new load? The marine wire gauge calculator sizes the wire and fuse for it to ABYC.
How the math works
Each load's daily energy is its watts times its hours times how many you run (two Pis or four cameras: set the Qty). Loads that run through a DC-DC converter, USB-C PD supply or PoE (Starlink, routers, computers, IP cameras) are divided by the converter efficiency, because the battery has to supply the losses as well. Everything after that is worked out from that battery-side number:
- Amp-hours a day = watt-hours a day ÷ battery voltage.
- Battery bank = amp-hours a day × days without charging ÷ usable fraction (0.8 for LiFePO4, 0.5 for AGM), rounded up to 100, 200, 300, 400 or 600 Ah.
- Solar = watt-hours a day ÷ (peak sun-hours × 0.7), rounded up to 100, 200, 300, 400 or 600 W. The 0.7 is the real-world derate from our solar guide.
- Charge controller = the smallest controller rated for your array: at 12 V, a Victron 75/15 up to 220 W, a 100/30 up to 440 W, a Renogy Rover 40A up to 520 W and a Victron 100/50 up to 700 W (double those at 24 V). The ratings come from our solar guide and MPPT guide; above the rating the controller simply caps its output.
Past the largest size in each list, the calculator shows the computed number and says so, instead of quietly capping it.
Where every number comes from
Every default is either published in one of our guides (and sourced there) or taken from a manufacturer's spec sheet. Your own boat will differ: edit the watts and hours to match, or measure with a shunt battery monitor.
| Load | Default | Published range | Source |
|---|---|---|---|
| Starlink MiniInternet · via converter | 30 W × 8 h | 20–40 W average, 15 W idle | Our guide Starlink figures as published in our Starlink guide |
| Starlink Standard 4 / 4 XInternet · via converter | 87 W × 8 h | 75–100 W average, about 20 W idle | Our guide |
| Starlink Standard Actuated (used)Internet · via converter | 62 W × 8 h | 50–75 W average | Our guide |
| Starlink Performance (Gen 2)Internet · via converter | 130 W × 8 h | 110–150 W average, about 45 W idle | Our guide |
| Cellular router (Peplink / Teltonika / GL.iNet)Internet · via converter | 8 W × 24 h | 3–14 W across our picks | Our guide Teltonika ~3 W idle, 9 W max; GL.iNet quotes under 14 W |
| Marina Wi-Fi boosterInternet · via converter | 5 W × 24 h | 5 W maximum (PoE) | Our guide |
| Cellular monitoring hub (Siren 3 Pro class)Monitoring & compute | 3.5 W × 24 h | 2–5 W | Our guide |
| Raspberry Pi 5 (headless, Signal K / HA)Monitoring & compute · via converter | 5 W × 24 h | 3–4 W idle, 12–25 W loaded | Our guide Default allows for sensors and a light load |
| Mini PC (N150 class)Monitoring & compute · via converter | 8 W × 24 h | 6 W idle, 18–22 W loaded | Our guide |
| NMEA 2000 gatewayMonitoring & compute | 2 W × 24 h | 1–3 W | Our guide |
| PoE / Ethernet switch (12 V)Network & sensors | 2 W × 24 h | 0.5 W idle, about 2 W with five devices busy | wiki.teltonika-networks.com Measured: Teltonika TSW101 0.48 W idle, 1.93 W with 5 LAN devices and heavy traffic at 12 V. The switch itself only; power it sends to cameras is counted on their rows |
| IP camera (PoE)Network & sensors · via converter | 4 W × 24 h | 4 W maximum; larger IR cameras up to 10 W | techspecs.ui.com Spec: UniFi G5 Bullet 4 W maximum, IR night vision included. Reolink lists up to 10 W for its single-lens PoE cameras under 8 MP. "Via converter" covers the switch stepping 12 V up to 48 V for PoE |
| SSD (on the Pi or mini PC)Network & sensors · via converter | 1 W × 24 h | 0.06 W idle, 4–5 W reading or writing | storagereview.com Spec: Samsung 990 EVO Plus 1 TB 60 mW idle, 4.3 W read, 4.2 W write (Samsung figures as listed in this review). Default assumes a mostly idle drive with steady logging |
| Wi-Fi sensor node (ESP32 / SensESP)Network & sensors | 0.5 W × 24 h | about 0.33 W with Wi-Fi listening | documentation.espressif.com Derived from the chip datasheet, not a measured product: ESP32 95–100 mA receiving at 3.3 V (Table 5-4). Default 0.5 W allows for the 12 V regulator and the sensors attached |
| MFD, 12-inchHelm | 16 W × 6 h | about 16 W typical, up to 45 W at full brightness | www8.garmin.com Spec: Garmin GPSMAP 8x12 1.3 A typical at 12 V ≈ 16 W; 6.0 A / 45 W maximum (checked 2026-11-10; was 32 W) |
| MFD, 9-inchHelm | 16 W × 6 h | about 16 W typical | www8.garmin.com Spec: 1.37 A typical at 12 V ≈ 16 W (Garmin GPSMAP 9x3 sonar model; 1.34 A non-sonar) |
| Solid-state radar domeHelm | 35 W × 4 h | 25–45 W | Our guide |
| AIS Class B+ transceiverHelm | 3.4 W × 8 h | about 3.4 W average | em-trak.com Spec: em-trak B954 (5 W SOTDMA, with splitter) 280 mA / 3.35 W average at 12 V with wireless on; 245 mA / 2.9 W with it off |
| VHF radio (standby)Helm | 5.4 W × 12 h | about 5 W on standby | standardhorizon.com Spec: 0.45 A standby at 12 V ≈ 5.4 W (Standard Horizon GX1800/GX1850; 0.8 A at full audio) |
| Autopilot, hydraulic (average while steering)Helm | 60 W × 4 h | about 5 A average (hydraulic) | static.garmin.com Spec: Garmin SmartPump v2 engaged 5–10 A (60–120 W at 12 V); default is the low end, moderate conditions |
| 12 V fridge (compressor, ~40% duty)Living | 18 W × 24 h | ~45 W running, ~18 W average | secop.com Spec: Secop BD35F compressor 45 W running (2,500 rpm, 12 V); ~40% duty ≈ 18 W average |
| LED anchor lightLiving | 3.5 W × 10 h | 2–5 W | Our guide |
| LED nav lightsLiving | 3.5 W × 2 h | about 3.5 W for a tricolour | hellamarine.com Spec: Hella NaviLED TRIO port, starboard and stern under 3.5 W combined; a steaming light adds more under power |
| LED cabin lightingLiving | 9 W × 4 h | about 9 W (three 3 W fixtures) | hellamarine.com Spec: Hella EuroLED 75 under 3 W (under 0.19 A at 12 V) each; default is three fixtures |
| Bilge pump (intermittent average)Living | 6 W × 24 h | 3–10 W average | Our guide |
| Fresh-water pump (average)Living | 1.5 W × 24 h | about 1.5 W averaged over a day | pentair.com Spec: Shurflo 4008 6.0 A at 40 psi ≈ 72 W running; ~30 min/day ≈ 1.5 W average |
| Cabin fansLiving | 13 W × 8 h | about 13 W (two 6.5 W fans) | hellamarine.com Spec: Hella 2 Speed Turbo fan 6.5 W; default is two fans |
What this calculator leaves out
- Engine and shore charging. It sizes for days at anchor, which is the case that runs batteries flat.
- AC loads through an inverter. Add them as a custom load with the inverter's draw included (roughly the AC watts ÷ 0.9).
- Wind and hydro generation, and 48 V systems.
- Shading, temperature and battery ageing. The derate covers typical losses, not a panel half-shaded by the boom.
Frequently asked questions
How big a battery do I need to run Starlink on a boat?
A Starlink Mini averaging 30 W for 8 hours a day through a DC-DC converter uses about 276 Wh, or 23 Ah at 12 V. Two days of that from LiFePO4, which you can use to 80%, needs about 57 Ah, so a 100 Ah lithium battery covers the Mini alone. A Standard 4 X at 87 W for the same 8 hours uses about 800 Wh a day and wants a 200 Ah lithium bank.
Why does the AGM bank come out so much bigger than lithium?
Lead-acid batteries, AGM included, should only be run down to about 50% to keep their cycle life, while LiFePO4 is routinely used to 80%. For the same usable energy an AGM bank needs about 1.6 times the rated amp-hours.
How much solar do I need to run a boat fridge?
A 12 V compressor fridge averages about 18 W over a day, or 432 Wh. With 4 peak sun-hours and panels delivering 70% of their rating, that is about 154 W of panel, so a 200 W panel.
Why does the calculator add converter losses?
Starlink, routers and onboard computers usually run from a DC-DC converter or USB-C PD supply rather than straight off the battery. A good isolated converter is about 87% efficient, so the battery supplies about 15% more energy than the device uses. Loads marked 'via converter' include that loss.
Does the calculator count alternator or shore-power charging?
No. It sizes the bank and solar for days at anchor with no engine running and no shore power, which is the case that runs batteries flat. Engine hours and marina nights only add margin.